Question about "/etc/sysctl.conf"

[nhouse]

Hi Folks... I came upon a suggestion about optimizing the sysctl.conf file HERE and would like your opinion please. I am learning all the time it seems about new things to optimize my server (yea, small potato guy with 1 DA server ). Here is the suggestion for you to look over... I have CentOS 4.3, by the way. Is this a good thing?

Kernel sysctl configuration file for Red Hat Linux
#
# For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and
# sysctl.conf(5) for more details.

# Disables packet forwarding
net.ipv4.ip_forward=0

# Disables IP source routing
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.lo.accept_source_route = 0
net.ipv4.conf.eth0.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0

# Enable IP spoofing protection, turn on source route verification
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.lo.rp_filter = 1
net.ipv4.conf.eth0.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1

# Disable ICMP Redirect Acceptance
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.lo.accept_redirects = 0
net.ipv4.conf.eth0.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0

# Enable Log Spoofed Packets, Source Routed Packets, Redirect Packets
net.ipv4.conf.all.log_martians = 0
net.ipv4.conf.lo.log_martians = 0
net.ipv4.conf.eth0.log_martians = 0

# Disables IP source routing
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.lo.accept_source_route = 0
net.ipv4.conf.eth0.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0

# Enable IP spoofing protection, turn on source route verification
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.lo.rp_filter = 1
net.ipv4.conf.eth0.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1

# Disable ICMP Redirect Acceptance
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.lo.accept_redirects = 0
net.ipv4.conf.eth0.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0

# Disables the magic-sysrq key
kernel.sysrq = 0

# Decrease the time default value for tcp_fin_timeout connection
net.ipv4.tcp_fin_timeout = 15

# Decrease the time default value for tcp_keepalive_time connection
net.ipv4.tcp_keepalive_time = 1800

# Turn off the tcp_window_scaling
net.ipv4.tcp_window_scaling = 0

# Turn off the tcp_sack
net.ipv4.tcp_sack = 0

# Turn off the tcp_timestamps
net.ipv4.tcp_timestamps = 0

# Enable TCP SYN Cookie Protection
net.ipv4.tcp_syncookies = 1

# Enable ignoring broadcasts request
net.ipv4.icmp_echo_ignore_broadcasts = 1

# Enable bad error message Protection
net.ipv4.icmp_ignore_bogus_error_responses = 1

# Log Spoofed Packets, Source Routed Packets, Redirect Packets
net.ipv4.conf.all.log_martians = 1

# Increases the size of the socket queue (effectively, q0).
net.ipv4.tcp_max_syn_backlog = 1024

# Increase the tcp-time-wait buckets pool size
net.ipv4.tcp_max_tw_buckets = 1440000

# Allowed local port range
net.ipv4.ip_local_port_range = 16384 65536

 

[eymbo]

Hello there,

I have tested sysctl tweaks on many servers and they all work fine after the tweaks are made. I recommend you to add these to the sysctl file as it's beneficial to network performance and will block some syn floods.

 

[nhouse]

Thanks... I appreciate the input. Can you sense any significant performance boosts after you added these tweaks?

 

[eymbo]

http://www.eth0.us/node/74

The above link may help.

I haven't noticed any significant increases in performance with your posted adjustments and the above link. I'm on a 100mbit link for my server and it only uses around 2mbps max on average so it isn't network performance demanding.

 

[jonn]

some lines are duplicated.

# Disables IP source routing
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.lo.accept_source_route = 0
net.ipv4.conf.eth0.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0

# Enable IP spoofing protection, turn on source route verification
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.lo.rp_filter = 1
net.ipv4.conf.eth0.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1

# Disable ICMP Redirect Acceptance
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.lo.accept_redirects = 0
net.ipv4.conf.eth0.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0

I added your example to my file and then did this when finished.
This was sourced from http://www.eth0.us/sysctl

After you make the changes to the file you need to run /sbin/sysctl -p and sysctl -w net.ipv4.route.flush=1 to enable the changes without a reboot.

The rules were taken from: http://ipsysctl-tutorial.frozentux.net/ipsysctl-tutorial.html

 

[jonn]

holy crap, after doing the above my server speed is so fast.